Instructions

RGB Eco Smoothswing Instructions

Press and hold the LED button to bring you out of sleep mode. You will hear a “power on” voice and the LED button will turn on.

Press and hold the button once, quickly, to turn the blade on.

The following controls activate when the blade is on and are based on the flash of the LED button light:

• A quick press will initiate a single blaster deflect effect.
• Press and hold the button for one flash, then release. This will initiate the lockup effect. A quick press will end the lockup effect.
• Press and hold the button for two flashes, then release. This will initiate the colour cycle. A quick press will end the cycle when the colour you want shows.
• Press and hold the button for 3 flashes to enter the quick colour select. When a colour you like appears, press the button once to exit.
• Press and hold past three flashes to shut off the blade.

While the blade is off, the following controls are activated based on the flash of the LED button light:

• Press and hold the button for one flash, then release. This will change the volume. There are 3 settings: Volume high, Volume low and mute.
• Press and hold the button for two flashes, then release. This will change the blade effect. There are 3 blade effects: Steady, Pulse and Unstable
• Press and hold the button for three flashes, then release. This will change the sound font to the next selection.
• Press and continue to hold past the third flash for approximately 10 seconds to put the saber back into sleep mode.

 You mustn’t let the battery fully discharge so our advice is to fully charge the saber when it says low battery or if you haven’t used it in a while.

Xenopixel Instructions

Basic controls:

Press and hold the LED button to bring you out of sleep mode. You will hear a “power on” voice and the LED button will turn on.

Press and hold the button once, quickly, to turn the blade on.

The following controls activate when the blade is on and are based on the flash of the LED button light:

• A quick press will initiate a single blaster deflect effect.
• Press and hold the button for one flash, then release. This will initiate the drag effect. A quick press will end the drag effect.
• Press and hold the button for two flashes, then release. This will initiate the colour cycle. A quick press will end the colour cycle when the colour you want shows.
• Continue and hold past two flashes to turn off the blade

 While the blade is off, the following controls are activated based on the flash of the LED button light:

• Press and hold the button for one flash, then release. This will change the volume. There are 3 settings: Volume high, Volume low and mute.
• Press and hold the button for two flashes, then release. This will change the blade effect. There are 5 blade effects: Steady, Pulse, Rainbow blade, Unstable and Fire blade.
• Press and hold the button for three flashes, then release. This will change the blade mode. There are several blade modes, including some pre on effects. Blade effect will affect pre on’s but will not have any effects on Blaster blade and Ghost blade modes. Only blade colour and font selection impact these modes.
• Press and hold the button for four flashes, then release. This will change the sound font. The selection of fonts can be customized by the user.

Advanced Control Motions:

There are several motions or manual controls available on the Xenopixel.

• A direct and quick stabbing motion with the hilt level will turn the blade on or off.
• A quick twist while the hilt is pointed down will change the font to the next on the list. Either direction will prompt the change as long as the hilt is pointed downwards.
• A quick twist while the hilt is pointed up will play a music track if one or more are available in the selected fonts folder. A quick twist again will stop the music.
• Hold the button and impact the hilt/blade to activate lockup. Release the button to end lockup.
• A quick twist while the hilt is pointed down will change the selected blade colour while holding the button down. Release the button to select the current colour.
• While holding the button, a quick twist while the hilt is pointing up will play a special effect. This will also play a sound if the correct file is included in the font.

For further help and support with Xenopixel please contact us directly as we can provide firmware updates and videos on how to remove the SD card and use the features described above.